Universali vieno užvedimo mygtuko sistema Nuotolinio užvedimo stabdymo beraktė įvedimo sistema Variklio užvedimo signalizacijos sistema

Please kindly Note: If the original car was equipped with a steering wheel lock and  chip anti-theft , before to modify one-button start ,the car must be released from the original car steering wheel lock and chip anti-theft and then can be used normally Model 1 Model 1 function : 1. RFID car anti-theft function 2. One-button engine start, one-button engine off 3. Unique foot brake detection function to prevent accidental starting of the car 4. Automatically lock the engine after turning off the engine for 30 seconds and the car cannot be started again without the RFID 5. Independently turn on ACC or ON power for listening to music, etc. 6. Long press the start button, the motor start time is up to 3 seconds (suitable for different vehicles and different climates to start vehicles) 7. Adopting RFID technology, Not need change the battery all life, and it is more effective to prevent interception and decoding 8. Static working current ≤25mA, no longer worry about losing the battery power of the car Model 2 Specifications Fit For:12V battery car, van, pickup truck, SUV, etc., general purpose products Operating Voltage:12V±3V Quiescent Current:less than 10mA Working Frequency:433MHz Features -Q6C intelligent one key to start the system, using smart chips, can provide a key to start / flameout, convenient and simple. -PKE keyless entry, automatic sensor switch lock function, near the car 2 meters, the automatic sensor unlock. -There is a remote start / flameout, countdown ten minutes off function. -Summer cool car, winter warm car, no longer bear the car when the uncomfortable. -With the identity function, the remote control is not able to start normally. Key Operation -Do not press the brake, short press to open the ACC sound, then press the on dashboard, the indicator light flashes, then short press off, you can cycle operation. -Brakes, short press, the system ignition start, light long light. -When the flame is turned on, the brakes are short pressed and the system is turned off. -Step on or not brakes, long press, the system can let go after the ignition, light long light Function 1. One-key start/stop 2. Remote control start/stop 3. Smart handbrake detection 4. Intelligent oil pump startup detection 5. Remote trunk open 6. Remote car search (horn buzzing, blinking indicator lights) 7. Open door flashing warning function when parking on the roadside 8. After locking the door, prying the door triggers the alarm prompt function 9. Remotely unlock/close the lock 10. PKE keyless comfortable entry function, automatically unlocks the door 1.5-3 meters away from the car, and automatically locks the door 3-5 meters away from the car 11. PKE induction temporary shutdown function 12. RFID identification 13. Anti-theft alarm function (Illegal opening the door, stepping on the foot brake to trigger an alarm prompt) 14. Engine engine lock function (the vehicle cannot be started in the car after the door is locked) 15. After starting, step on the foot brake to automatically lock the door, and automatically unlock when the flame is turned off 16. Start the automatic lock, turn off the lock automatically 17. Original car horn alarm prompt (can add alarm horn) 18. Power off memory 19. Emergency reset function 20. Remotely start and turn off the flame in 10 minutes Package Included: 1 x Host 2 x Remote Control Handle 1 x Start Button 2 x Sensing Antenna 1 x Start Harness 1 x Detection Harness 1 x Restore Button 1 x Manual Q&A : 1.How to find the ACC wire? Please rearrange the 6P cable, after you twist the key to the first gear position (you can listen to music at this time), measure the line that has electricity on your original car is the ACC line. 2. For your 6p cable, but my original car is only 5p. what can i do ? If your original car is a 5P line, the right connection is normally 1 power line, 1 ACC line, 2 ON lines, and 1 start line. If you didn t follow this step, it means you got wrong installation. pls recheck it again. and pls remember 2 ON lines need to distinguish which is ON1 line and which is ON2 line. If the two ON lines are always charged at the time of startup, you need to connect the two ON lines in parallel. 3. How to tell the wire ON1 and ON2? If you test these two ON lines at startup, one of the two that always has power is the ON1 line. And If the other one has instant power is the ON2 wire.